Visit My Web Page

 

This post below about Tools You Need to Install a New Bathtub is relatively informative. Don't miss it.

Installing a bath tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old tub with a new one is additionally a reasonably tough project. If the old tub is conveniently accessible, the task can move easily; if you have to open up a wall to eliminate the old tub and also place the brand-new bathtub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old tub and set in the new one. Ensure you have actually qualified on your own for the work and also fit trying it. As opposed to employing a specialist to take control of a halfway-completed job, it is better to think about employing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This short article will certainly aid you mount a brand-new bathtub in your bathroom if you have actually currently bought a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and material checklist ought to make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome due to the restricted access that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washers remain in place between the faucet and also the sink. Safeguard the faucet in position with the supplier supplied backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Setting up the Tub

Using both wood boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub up until the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the tub and additionally inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it right into its last placement.

 

 

Getting ready for the Setup

To start with, the supporting frame supplied with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the adaptable tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.

 

 

Tiling Around the Bathtub

In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break an inflexible seal, triggering the water to permeate the wall surface between the bath and the tiling, causing issues with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can split relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently readily available on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We were shown that report on Installing A Bathtub from a good friend on a different web property. Are you aware of somebody else who is excited by the subject? Take a moment to share it. We love reading our article about A Step-by-Step Guide to Installing a Bathtub.

Learn More